Fast delivery
Get in as fast as 1 hour
It’s all local
Shop your favorites
Direct chat
Connect with shoppers
About
Details
10 mins. Fast & easy. Reusable. R-134a trigger. Dispenser & gauge. No. 1 super chill formula. Ultra synthetic. Maximum cooling. Stops leaks. Extends system life. Smart Clip Technology: Smart Clips - changes color in vent to show correct fill. Smart Can - logo turns blue when refrigerant goes into A/C. Black Diamond Avalanche contains 17 oz. of R-134a (1,1,1,2 Tetrafluoroethane) and 1 oz. of no. 1 super chill formula to ensure maximum cold air while sealing common rubber o-ring, gasket, and hose leaks and extending compressor life. Smart clips, when inserted into the air vent, will change color to show that the system is fully charged. www.acavalanche.com. Scan to visit our website and to view our how to video. Facebook: Like us. Youtube: Watch us. For more information visit www.acavalanche.com. Made in USA from US & Imported parts.
Directions
Remove smart clip. Installation Instructions: 1. Remove both of the Smart Clips from the cap and insert them into vehicle's center air vent. 2. Locate the vehicle's low side service port. This port will often have a plastic cap and is located between the a/c compressor and the evaporator. It is the only port to which the recharge hose will connect. 3. Start the engine and turn air conditioner to maximum cool and maximum air flow. Close passenger compartment. 4. Tighten the recharge hose to the top of the Avalanche can by turning it clockwise. Make sure it is firmly attached. Shake can well. Connect the quick connect coupler to the low side service port by pulling the connector ring back as you push the fitting onto the service port. Make sure it locks into place. 5. Check gauge pressure when the compressor cycles on. Using the chart, determine the correct low-pressure PSI level in accordance with the ambient temperature. Read pressure when the clutch is cycled on. If the gauge needle is above the correct PSI level, check your compressor to see if it is cycling on. If the compressor does not engage, repairs may need to be performed. If gauge reads in the Red Zone and the compressor is cycled on, do not recharge. Seek a mechanic's assistance. Some vehicles with expansion valves cannot be accurately charged using low side pressure gauge only. If your gauge is not increasing, stop charging and check air vent temperature. The PSI may only increase to 25-30 psi on these systems. Ambient Temperature degrees F/degrees C: 65 degrees (18 degrees C); Low Pressure Gauge: 25-35 psi/172-241kPA. Ambient Temperature degrees F/degrees C: 70 degrees (21 degrees C); Low Pressure Gauge: 35-40 psi/241-276kPA. Ambient Temperature degrees F/degrees C: 75 degrees (24 degrees C); Low Pressure Gauge: 35-45 psi/241-310kPA. Ambient Temperature degrees F/degrees C: 80 degrees (27 degrees C); Low Pressure Gauge: 40-50 psi/276-345kPA. Ambient Temperature degrees F/degrees C: 85 degrees (29 degrees C); Low Pressure Gauge: 45-55 psi/310-379kPA. Ambient Temperature degrees F/degrees C: 90 degrees (32 degrees C); Low Pressure Gauge: 45-55 psi/310-379kPA. Ambient Temperature degrees F/degrees C: 95 degrees (35 degrees C); Low Pressure Gauge: 50-55 psi/345-379kPA. Ambient Temperature degrees F/degrees C: 100 degrees (38 degrees C); Low Pressure Gauge: 55-50 psi/345-379kPA. Ambient Temperature degrees F/degrees C: 105 degrees (41 degrees C); Low Pressure Gauge: 50-55 psi/345-379kPA. Ambient Temperature degrees F/degrees C: 110 degrees (43 degrees C); Low Pressure Gauge: 50-55 psi/345-379kPA. 6. Hold can upright to charge. Squeeze trigger to add refrigerant while fully rotating the can from a 12 o'clock position to 3 o'clock position, continually agitating (sweeping) can back and forth. The word Avalanche will turn from white to blue indicating refrigerant is being added to the system. If your system is very low in refrigerant this process can take several minutes. Do not overcharge/do not vent. 7. Check pressure every 10-15 seconds by releasing the trigger. Continue process until the needle of the gauge reaches the low-pressure PSI level according to the chart. Remove quick-connect coupler from the service port and check the smart clips while increasing your RPM slightly with closed passenger compartment. One clip will change to blue showing the a/c is approaching optimum fill. The second clip will change to green showing the system is sufficiently charged. (If outside temperature is above 95 degrees only the blue clip needs to change for sufficient refrigerant fill.) Never place refrigerant can on any hot engine part. 8. When you have the correct fill and your air conditioner is blowing cold, stop charging. Remove the quick-connect coupler from the service port and store can in a cool, dry place or discard according to state or local guidelines. The hose can be detached and re-used.
Warnings
Caution: Always wear protective rubber gloves and eye wear., Warning: Contents under pressure. Read cautions on back. Do not store above 120 degrees F. Danger: Store in a cool place - never in passenger cabin of vehicle as can may explode. Do not expose to temperatures above 120 degrees F. Do not puncture or incinerate. Never place refrigerant can on any hot engine part. Not for use on hybrid/electric vehicles with non-belt driven (electric driven) compressor. Keep out of reach of children. Exposure to skin may cause frostbite. Flush with warm water. If sprayed into eyes, flush with warm water. If inhaled, remove to fresh air and call physician immediately. Contains 1,1,1,2 Tetrafluoroethane (CAS no. 811-97-2).
About
Details
10 mins. Fast & easy. Reusable. R-134a trigger. Dispenser & gauge. No. 1 super chill formula. Ultra synthetic. Maximum cooling. Stops leaks. Extends system life. Smart Clip Technology: Smart Clips - changes color in vent to show correct fill. Smart Can - logo turns blue when refrigerant goes into A/C. Black Diamond Avalanche contains 17 oz. of R-134a (1,1,1,2 Tetrafluoroethane) and 1 oz. of no. 1 super chill formula to ensure maximum cold air while sealing common rubber o-ring, gasket, and hose leaks and extending compressor life. Smart clips, when inserted into the air vent, will change color to show that the system is fully charged. www.acavalanche.com. Scan to visit our website and to view our how to video. Facebook: Like us. Youtube: Watch us. For more information visit www.acavalanche.com. Made in USA from US & Imported parts.
Directions
Remove smart clip. Installation Instructions: 1. Remove both of the Smart Clips from the cap and insert them into vehicle's center air vent. 2. Locate the vehicle's low side service port. This port will often have a plastic cap and is located between the a/c compressor and the evaporator. It is the only port to which the recharge hose will connect. 3. Start the engine and turn air conditioner to maximum cool and maximum air flow. Close passenger compartment. 4. Tighten the recharge hose to the top of the Avalanche can by turning it clockwise. Make sure it is firmly attached. Shake can well. Connect the quick connect coupler to the low side service port by pulling the connector ring back as you push the fitting onto the service port. Make sure it locks into place. 5. Check gauge pressure when the compressor cycles on. Using the chart, determine the correct low-pressure PSI level in accordance with the ambient temperature. Read pressure when the clutch is cycled on. If the gauge needle is above the correct PSI level, check your compressor to see if it is cycling on. If the compressor does not engage, repairs may need to be performed. If gauge reads in the Red Zone and the compressor is cycled on, do not recharge. Seek a mechanic's assistance. Some vehicles with expansion valves cannot be accurately charged using low side pressure gauge only. If your gauge is not increasing, stop charging and check air vent temperature. The PSI may only increase to 25-30 psi on these systems. Ambient Temperature degrees F/degrees C: 65 degrees (18 degrees C); Low Pressure Gauge: 25-35 psi/172-241kPA. Ambient Temperature degrees F/degrees C: 70 degrees (21 degrees C); Low Pressure Gauge: 35-40 psi/241-276kPA. Ambient Temperature degrees F/degrees C: 75 degrees (24 degrees C); Low Pressure Gauge: 35-45 psi/241-310kPA. Ambient Temperature degrees F/degrees C: 80 degrees (27 degrees C); Low Pressure Gauge: 40-50 psi/276-345kPA. Ambient Temperature degrees F/degrees C: 85 degrees (29 degrees C); Low Pressure Gauge: 45-55 psi/310-379kPA. Ambient Temperature degrees F/degrees C: 90 degrees (32 degrees C); Low Pressure Gauge: 45-55 psi/310-379kPA. Ambient Temperature degrees F/degrees C: 95 degrees (35 degrees C); Low Pressure Gauge: 50-55 psi/345-379kPA. Ambient Temperature degrees F/degrees C: 100 degrees (38 degrees C); Low Pressure Gauge: 55-50 psi/345-379kPA. Ambient Temperature degrees F/degrees C: 105 degrees (41 degrees C); Low Pressure Gauge: 50-55 psi/345-379kPA. Ambient Temperature degrees F/degrees C: 110 degrees (43 degrees C); Low Pressure Gauge: 50-55 psi/345-379kPA. 6. Hold can upright to charge. Squeeze trigger to add refrigerant while fully rotating the can from a 12 o'clock position to 3 o'clock position, continually agitating (sweeping) can back and forth. The word Avalanche will turn from white to blue indicating refrigerant is being added to the system. If your system is very low in refrigerant this process can take several minutes. Do not overcharge/do not vent. 7. Check pressure every 10-15 seconds by releasing the trigger. Continue process until the needle of the gauge reaches the low-pressure PSI level according to the chart. Remove quick-connect coupler from the service port and check the smart clips while increasing your RPM slightly with closed passenger compartment. One clip will change to blue showing the a/c is approaching optimum fill. The second clip will change to green showing the system is sufficiently charged. (If outside temperature is above 95 degrees only the blue clip needs to change for sufficient refrigerant fill.) Never place refrigerant can on any hot engine part. 8. When you have the correct fill and your air conditioner is blowing cold, stop charging. Remove the quick-connect coupler from the service port and store can in a cool, dry place or discard according to state or local guidelines. The hose can be detached and re-used.
Warnings
Caution: Always wear protective rubber gloves and eye wear., Warning: Contents under pressure. Read cautions on back. Do not store above 120 degrees F. Danger: Store in a cool place - never in passenger cabin of vehicle as can may explode. Do not expose to temperatures above 120 degrees F. Do not puncture or incinerate. Never place refrigerant can on any hot engine part. Not for use on hybrid/electric vehicles with non-belt driven (electric driven) compressor. Keep out of reach of children. Exposure to skin may cause frostbite. Flush with warm water. If sprayed into eyes, flush with warm water. If inhaled, remove to fresh air and call physician immediately. Contains 1,1,1,2 Tetrafluoroethane (CAS no. 811-97-2).
Common questions
Learn more about how to place an order here.
Then, when you arrive at the store of your choice, use the Instacart app to notify us. Depending on the store, a shopper or store employee will bring the groceries to your car, or you can pick them up at the designated area.
Learn more about pickup orders here.
- Delivery fees start at $3.99 for same-day orders over $35. Fees vary for one-hour deliveries, club store deliveries, and deliveries under $35.
- Service fees vary and are subject to change based on factors like location and the number and types of items in your cart. Orders containing alcohol have a separate service fee.
- Tipping is optional but encouraged for delivery orders. It's a great way to show your shopper appreciation and recognition for excellent service. 100% of your tip goes directly to the shopper who delivers your order.
With an optional Instacart+ membership, you can get $0 delivery fee on every order over $35 and lower service fees too.
Instacart pickup cost:
- There may be a "pickup fee" (equivalent to a delivery fee for pickup orders) on your pick up order that is typically $1.99 for non-Instacart+ members. Instacart+ membership waives this like it would a delivery fee.
- Pick up orders have no service fees, regardless of non-Instacart+ or Instacart+ membership.
Learn more about Instacart pricing here.
You can set item and delivery instructions in advance, as well as chat directly with your shopper while they shop and deliver your items. You can tell the shopper to:
- Find Best Match: By default, your shopper will use their best judgement to pick a replacement for your item.
- Pick Specific Replacement: You can pick a specific alternative for the shopper to purchase if your first choice is out-of-stock.
- Don't Replace: For items you'd rather not replace, choose "Don't replace" to get a refund if the item is out of stock.
Learn more about instructions for specific items or replacements here.
- Missing items
- Incorrect items
- Damaged items
- Poor replacements
- Early/late orders
If an order never came, or you get someone else's order, you can reach out to Instacart Customer Experience.